MIX320-A AVIOM
Personal Mixing System
Aviom’s Mix320-D Personal Mixing System has been designed specifically for use with Dante™ enabled consoles and networks. It includes everything you need to create a personal mixing system for six performers. The A320 Personal Mixers get their digital data and power over the same cable, so all you need to do is connect a Cat-5 cable and you're ready to start using the system. The Mix320-D Personal Mixing System makes it easy to add Aviom monitoring to a Dante-enabled mixing console or audio network. No analog input module or console card is required; inputs get patched directly from your Dante network.
The Mix320-D system includes a D400-Dante A-Net Distributor that allows up to 32 channels to be patched from the Dante network to the personal mixing system inputs. The D400-Dante is also used to supply A-Net digital data and DC power to the mixers. The Mix320-D system includes six A320 Personal Mixer for the performers, plus six MT-1a Mic Stand Mounts for attaching the A320 mixers to mic stands, as well as all the Cat-5e cables you'll need to connect the products.
Intuitive Mixing
The A320 Personal Mixer gives performing and recording musicians simple, intuitive control over their monitor mixes. It features a 32-channel mix engine with 16 mono or stereo mix channels buttons and easy to use Stereo Placement controls. Connect headphones, ear buds, or a wireless in-ear monitoring system to the Personal Mixer and you're ready to start mixing.
Distribute Power and Audio Over Cat-5
For distributing the A-Net digital data and DC power to the A320 Personal Mixers, the system includes the D400-Dante A-Net Distributor. The D400-Dante also serves as the system's input device; it allows up to 32 channels from your Dante network to be assigned to the eight powered A-Net ports on its front panel. Stereo Link switches allow adjacent channels to be treated as a stereo pairs on the A320 Personal Mixers where they will appear on a single mix channel button.
System Options
The Mix320-D system uses a Dante network for its inputs. If you use a digital console, check out the Mix320-Y Personal Mixing System which includes a Y1 card for Yamaha® consoles for its inputs. Or, if you have an analog console or recording system, the Mix320-A Personal Mixing System is what you need. It includes the 16-channel, line-level AN-16/i Input Module as its front end. The mixing system packages are also easy to expand when you're ready—just add more Personal Mixers and A-Net Distributors as needed.
Includes:
-
(1) D400-Dante A-Net Distributor
-
(6) A320 Personal Mixers
-
(6) MT-1a Mic Stand Mounts
-
(7) Cat-5e cables
A320 Specifications:
-
Audio Output: 1/4" TRS stereo, headphone or line level
-
Stereo Mix Output, Headphone/Line
-
Tip: Audio Left
-
Ring: Audio Right
-
Sleeve: Ground
-
A-Net I/O: 1 A-Net In, RJ45 connector; Supports Pro16and Pro16e
-
D/A Conversion: 44.1/48kHz, 24-bit
-
Stereo Operation: Stereo Link, per channel pair set at the input module
-
Variable pan per mono channel or pan/spread per stereo channel pair
-
Headphone Output: 275 mW per side into 50 Ohms (both sides driven)
-
Output Impedance: 5 Ohms
-
Freq. Response: 3Hz-22kHz +0.2dB/-3dB at 50 Ohms
-
THD +N: < 0.003%
-
Output Voltage for Personal Mixers: 24VDC, 0.5 amp
-
Transmitted over the Cat-5e cable
-
Signal to Noise (unweighted): -106dB (measured with zero data into all channels)
-
Latency: 0.880 msec (measured from analog input to analog output)
-
Pro16e A-Net: Use Cat-5e (or better) cable
-
Maximum 400 ft (122 m) between devices
-
Supports Power Over A-NetCat-5 cable: Use shielded Cat-5e (or better) cable to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits.
-
Power: 24 VDC, 0.5 amp
-
Power is supplied over the Cat-5 cable when connected to an Aviom
A-Net Distributor:
-
Dimensions: 10.26" (260.6 mm) wide x 6.14" (155.95mm) deep x 1.91" (48.51 mm) high
-
Weight: 1.3 lbs. (0.59 kg)
-
Optional: MT-1a Mic Stand Mount
D400-Dante Specifications:
-
Dante Interface: 32 channels (44.1/48kHz Sample Rate)
-
Dante Primary I/O: RJ45 connector
-
Dante Secondary I/O: RJ45 connector
-
Dante LEDs: Network Activity (Green); 1GB Network Connection Active (Yellow)
-
A-Net Out to Personal Mixers: Eight RJ45 connectors, powered
-
A-Net Out: Pro16e A-Net
-
RJ45 connector, unpowered
-
LEDs: Power On (Red); Network Sync (Green)
-
Stereo Link: Two 8-position DIP switch blocks (1-16,17-32)
-
Output Voltage for Personal Mixers: 24VDC, 0.5 amp transmitted over the Cat-5e cable
-
A-Net Cables: Front Panel Connections: Shielded Cat-5e (or better) cable must be used to stay below the CISPR 22 Class B, ICES-003, and FCC 47 CFR Part 15 Class B emissions limits. Unshielded Cat-5e cable may be used on all rear panel connections
-
Power Supply: Internal, IEC connector
-
Input Voltage: 100-120 VAC or 200-240 VAC (with selector switch); 50-60Hz @220 W max
-
AC Fuse Types: 115V range: T2.5AL/250V, 230V range: T1.25AL/250V
-
Dimensions: 19" (482.6 mm) wide x 7.386" (187.6 mm) deep; 2U, 3.5" (88.9 mm) high
-
Weight: 12 lbs. (5.44 kg)
SALE: $3899.99
SAVE $100.00 AT CHECKOUT
USE PROMO CODE: $100-OFF
FREE S&H in continental US (e-mail for international / offshore USA rates)