YAMAHA PX5 1600w Rackmount DSP Amplifier

 PX5  YAMAHA 

 1600w Rackmount DSP Amplifier 

This advanced power amplifier combines intelligent processing with high output to meet the requirements of a vast range of sound reinforcement environments. Boasting 500W x 2 at 8 ohms and 800W x 2 at 4 ohms, the PX5 has plenty of punch to satisfy your power needs, along with advanced features that will make your life easier at your next event. Most notably, this little powerhouse delivers onboard equalization and settings for delays and crossovers—a huge bonus if you care about producing the best sound possible, but don't care much for lugging extra gear.

The Yamaha PX5 dual-channel amplifier is driven by a newly developed Class-D amplifier engine that concentrates all the necessary functions into a single custom LSI chip, and uses PLL technology to control transfer characteristics in real time, achieving impressive sound quality and power. This new single-chip architecture offers higher output and improved performance in a more lightweight, yet reliable design. A combination of cutting-edge technology and an exhaustive component selection process make PX Series amplifiers supremely efficient amplifiers with low noise, reliable protection features, and above all, outstanding sound quality.

DSP for audio processing
Amp Mode allows the user to configure the system without difficulty by selecting the input routing and output routing. A total of 15 types of patterns can be selected. - Input routing (Dual/Parallel/Single/SUM)- Speaker System Structure (FULL+FULL/SUB+SUB/FULL+SUB/Bi-Amp/Boost Full/Boost Sub)

Sophisticated Signal Processing
The PX5 comes with flexible onboard crossover, filters, delay, limiter and PEQ (fixed preset) functions as standard, allowing quick and easy system setup via the LCD display, without the need for any additional outboard gear. It also features Yamaha’s intelligent D-CONTOUR multi-band dynamic processing, allowing users to achieve consistent clarity and high-quality sound for either front-of-house or monitor configurations.

Easy, Intuitive Setup
To accommodate users with varying levels of sound reinforcement experience, the PX5 offers both Basic and Advanced setup modes. Basic mode allows even inexperienced users to easily configure a system that meets their needs, while Advanced mode offers experienced users more precise control over every aspect of their sound. The PX5 also features eight programmable presets for instant recall and reduced setup time that can be saved to a USB thumb drive and shared with other PX amplifiers.

Flexible Connectivity, Durable Construction
Equipped with both XLR and TRS inputs, and binding post, SpeakON and phone outputs, the Yamaha PX5 offers the flexibility needed for a variety of setups and environments, and the durability to stand up to extended road-use thanks to the sturdy chassis and carrying handle design.

Power Boost Mode
The PX5 also comes equipped with a Power Boost Mode that combines the power output from two channels into one, achieving significantly higher single-channel power levels to drive high power handling speakers when needed.

Smart Config Wizard
The Config Wizard allows users to save even more time during system setup by assigning optimized speaker settings that match your system configuration– simply select the appropriate filter and crossover for each speaker, and Config Wizard will do the rest. Config Wizard also features presets specifically tuned for each model in Yamaha’s extensive lineup of passive speakers, including the popular CBR, Club, Installation, and VXS/VXC series, and an advanced mode that allows more detailed configuration of parameters such as input routing, input sensitivity, amp gain, and speaker impedance.

Utilities for Safe and Secure Operation
The PX5 dual-channel amplifier makes it fast and easy to configure panel settings, monitor amplifier status, and transfer data via USB, and also feature a panel locking function to keep your settings safe. Users can even export information such as internal device and log data to USB for rapid troubleshooting should difficulties arise.

Features:

• Dual-channel power amplifier

• Redesigned Class-D engine with a custom LSI

• 500W x 2 at 8 ohms; 800W x 2 at 4 ohms

• Onboard PEQ and settings for delay and crossover

• Utilities for safe and secure operation

Specifications:

• Sampling frequency rate: 48 kHz

• A/D D/A Converters: AD/DA: 24-bit linear, 128 times over sampling

• Total harmonic distortion: 0.1% (1 kHz, 10W), 0.3% (1 kHz, Half power)

• Frequency response: ±1.0 dB (1W, 8 Ohms, 20 Hz to 20 kHz)

• S/N ratio: 101 dB (A-weighted, 8 Ohms, Gain setting = +14 dBu)

• Crosstalk: Less than -60 dB (Half Power, 8 Ohms, 1kHz, Vol max input 150 Ohm shunt)

Voltage Gain/Sensitivity

• 8O Volume max: 32.0 dB/+9.3 dBu (Gain setting: 32 dB), 26.0 dB/+15.3 dBu (Gain setting: 26 dB), 37.3 dB/+4 dBu (Gain setting: +4 dBu), 27.3 dB/+14 dBu (Gain setting: +14 dBu)

• 8O Volume max /Power Boost mode: 35.0 dB/+4.1 dBu (Gain setting: 32 dB), 29.0 dB/+10.1 dBu (Gain setting: 26 dB), 35.1 dB/+4 dBu (Gain setting: +4 dBu), 25.1dB/+14 dBu (Gain setting: +14 dBu)

• Maximum input voltage: +24 dBu

• Input impedance: 20 kOhms (Balance), 10 kOhms (Unbalance)

I/O Connectors

• Speaker output ports: Neutrik speak ON NL4 x2, Binding post x2 pairs, 1/4" PHONE (TS) x2

• Line Input: XLR-3-31 x2, 1/4 "PHONE (TRS) x2

• Others: USB 2.0 Standard-A Connector (Female) for Save/Load, Speaker preset update, Firmware update with USB memory; AC inlet x1 with AC cord clamp

• Indicators: POWER x1 (Green), ALERT x1 (Red), USB x1 (Green), PROTECT x2 (Red), CLIP/LIMIT x2 (Red), SIGNAL x2 (Green); Auto LED off feature

• Processors: Input summing; D-CONTOUR (FOH/MAIN, MONITOR, OFF); Delay (0 - 74msec); HPF/LPF (cutoff frequency 20 Hz~20 kHz with polarity control); Speaker Processor (6-band PEQ + Limiter + Delay)

• Latency: 1.5 msec (Analog Input to Speakers)

• Presets: 8 user amplifier presets (Factory preset: Speaker presets for Yamaha passive speakers)

Protection circuit

• Load protection: POWER switch on/off: Output mute; Output voltage protection: Over voltage limiter, user configurable by wattage and speaker preset; DC-fault: Power Supply shutdown (NOT restored automatically)

• Amplifier protection: Thermal: Output limiter (Restored automatically) –> Output mute (Restored automatically); Over current: Output mute (Restored automatically); Over voltage: Output limiter (Restored automatically); Integrated Power Limit: Output limiter (Restored automatically)

• Power supply protection: Thermal: Output limiter (Restored automatically) –> Power supply shutdown; Over voltage: Power supply shutdown; Over current: Power supply shutdown

• Amplifier class: Class D, Balanced output circuit (BTL)

• Cooling: 16 step variable speed fan x 2, front to rear airflow

• Power requirements: Depending on area of purchase; 100V 50Hz/60Hz, 120V 60Hz, 220V-240V 50Hz/60Hz *Verified as operating at rated power voltage +/- 10% voltage.

• Power consumption: 310W (1/8 MAX power, 4 Ohms, Pink noise at all channels), 60W (4 Ohms, Idling)

• Dimensions (W x H x D): 18-7/8" x 3-7/16" x 15-2/8" (480 x 88 x 388mm)

• Net weight: 15.21 lbs. (6.9 kg)

Environment

• Operating Temperature: 0° C to +40° C

• Storage temperature: -20° C to +60° C

SALE: $879.99 

FREE S&H in continental US (e-mail for international / offshore USA rates)